Nearly everybody has got his or her own thinking on the subject of Tools You Need to Install a New Bathtub .
Installing a bathtub isn't precisely rocket science, yet it does call for solid plumbing, woodworking, and in some cases, tiling abilities. Replacing an old bath tub with a new one is additionally a reasonably difficult project. If the old bathtub is easily obtainable, the task can move easily; if you have to open a wall to remove the old bathtub and also position the brand-new bathtub, the job is a lot harder. In either instance, the project is within a house handyman's abilities, although you will require a helper to leave the old bathtub and also embeded in the new one. Make sure you have actually qualified yourself for the task and are comfortable trying it. Instead of employing a contractor to take over a halfway-completed job, it is much better to consider employing one before you begin. Chances are you may require an expert plumber to make tube links.
This write-up will aid you set up a new bath tub in your bathroom if you have currently bought a new tub as well as don't need to alter the arrangement of your previous water pipelines.
Your tools as well as material list must comprise the following:
Planning for the Installment
To start with, the sustaining structure provided with the bath should be fitted (if needed) according to the supplier's guidelines. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is necessary to see to it that if the faucet includes a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the faucets unit to prevent strain on the bathtub.
Fit the flexible faucet adapters to the bottom of both faucets making use of 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet with the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. See to it you make use of every one of the supplied washers.
Connect the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath need to now be ready to be fitted in its last setting.
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you ought to do is detach the water. After doing so, activate the faucets to drain any water remaining in the system. The process of eliminating the existing faucets can be quite problematic as a result of the restricted access that is usually the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipelines to the taps. Have a towel all set for the remaining water that will originate from the pipes. When the supply pipelines have been eliminated, utilize the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the solitary faucets from transforming during this process. As soon as the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any old sealing substance.
Before moving on to fit the new faucets, contrast the pipeline links on the old taps to the brand-new faucets. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Setting up the Bathtub
Utilizing the two wood boards under its feet, put the tub in the needed setting. The wooden boards are helpful in equally spreading the weight of the tub over the area of the boards instead of focusing all the weight onto four small points.
The following goal is to ensure that the tub is leveled all round. This can be attained by checking the spirit level and also readjusting the feet on the tub till the level checks out degree.
To mount faucets, fit the bottom of the outermost flexible tap port to the appropriate supply pipe by making a compression join; after that do the same for the various other tap.
Switch on the supply of water and check all joints and also new pipework for leakages as well as tighten them if required. Fill up the bathtub as well as also inspect the overflow electrical outlet as well as the typical outlet for leaks.
Ultimately, repair the bathroom paneling as explained in the producer's instruction manual. Tiling and also securing around the tub should wait till the bath tub has actually been utilized a minimum of when as this will certainly resolve it right into its last placement.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will require a plastic port to stop damage to the thread. One end of the connector fits on the plastic tail of the tap as well as the various other end provides a link to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly require decreasing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, place the tap in the mounting opening in the bath/basin making sure that the washing machines remain in location between the faucet and also the sink. Safeguard the faucet in position with the supplier supplied backnut. When the faucet is firmly in position, the supply pipes can be connected to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with typical tap adapters. The former kind should be connected to the tap ends first, tightening up only by hand. The supply pipes can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the area where the bathroom fulfills the tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the installation can relocate enough to fracture an inflexible seal, creating the water to penetrate the wall surface in between the bath as well as the tiling, resulting in difficulties with moisture as well as possible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your components and also fittings. They are sold in tubes and also cartridges, as well as can sealing spaces up to a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with spins of drenched paper or soft rope. Remember to always fill the tub with water before securing, to enable the motion experienced when the bathtub is in use. The sealant can split fairly early if you do not take into account this movement before securing.
Conversely, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally conveniently available on the marketplace. It is recommended to fit the floor tiles making use of waterproof or waterproof adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We hope you liked our excerpt about Tools You Need to Install a New Bathtub . Thanks so much for taking the time to read our blog. Do you know about someone else who is serious about the subject? Feel free to promote it. Bless you for your time. Visit again soon.
Immediate attention? Call!